Cadac LIVE1 Bedienungsanleitung PDF herunterladen (Seite 25)

Revision L1.1 2011-12Live1

Su/jointfilesconvert/1717682/bgroup meters:

METER – the signal level in each su/jointfilesconvert/1717682/bgroup (or auxiliary

send – see below) may be monitored by the 10-segment

LED bargraph meter at the top of each su/jointfilesconvert/1717682/bgroup strip. Note

the bottom LED is labelled SIG, and illuminates at a signal

level of approx. -36 dBu. The LEDs are colour-coded as

follows:

red: +18 dBu

yellow: -24 dBu to +12 dBu

green: SIG

GRP/AUX – the meters may be individually switched to monitor the level of Aux.

Sends 1 to 4 instead of that of the su/jointfilesconvert/1717682/bgroups. Pressing this button selects AUX,

and an adjacent red LED illuminates to conﬁ rm the setting. This is useful during

set-up when the console is being used for FOH work, when FX send levels may

be set and then left, the meters being returned to su/jointfilesconvert/1717682/bgroup mode during the

show. When the Live1 is being used as a monitor mixer, normal practice would

be to switch all these meters to AUX permanently.

Note that the meters show pre-fade signals whether set to GRP or AUX; i.e., in

GRP mode, they indicate the su/jointfilesconvert/1717682/bgroup level pre the su/jointfilesconvert/1717682/bgroup fader, and in AUX

mode, the Aux send level pre the Aux Master fader.

L-R – pressing this button sends the post-fade su/jointfilesconvert/1717682/bgroup signal to the

L-R master section, via the PAN control. An adjacent red LED illuminates

to conﬁ rm the routing. The su/jointfilesconvert/1717682/bgroup signals are still available at the rear

panel GP1 – GP4 connectors even if this routing is not selected.

PAN – allows the mono su/jointfilesconvert/1717682/bgroup to be panned anywhere in the stereo

image of the L-R Master output. When in its centre (0) position, the

su/jointfilesconvert/1717682/bgroup signal is centrally positioned in the stereo mix.

PFL – pressing the PFL button routes the su/jointfilesconvert/1717682/bgroup to the internal

PFL/AFL system so that it may be monitored on local speakers or

headphones connected at the MON OUT or HEADPHONES connectors

respectively. The su/jointfilesconvert/1717682/bgroup continues to operate normally while the PFL

button is pressed. An adjacent green LED illuminates to conﬁ rm that

PFL/AFL is active.

Like the input channels, the su/jointfilesconvert/1717682/bgroups may be monitored either pre-fade

(PFL) or after-fade (AFL); the mode is selected globally from the Master

section (see “AFL Mode” on page 29). In PFL mode, the signal is

heard in mono, and the su/jointfilesconvert/1717682/bgroup fader and MUTE button have no effect

on the level. In AFL mode, the signal is heard in stereo, at the correct

position in the L-R Master image, as determined by the su/jointfilesconvert/1717682/bgroup PAN

control. In this case, the channel fader setting will affect the level of the

signal heard, but the MUTE button will have no effect.

M – Pressing the M (MUTE) button mutes the su/jointfilesconvert/1717682/bgroup; this includes the rear

panel GROUP output and routing to the L-R Master (if selected). The exception

is PFL/AFL monitoring, which remains active. An adjacent red LED illuminates

to conﬁ rm that MUTE is applied.

Fader – a 100 mm plastic conductive fader with a blue knob adjusts the overall

su/jointfilesconvert/1717682/bgroup level. The pre-fade su/jointfilesconvert/1717682/bgroup signal may be metered at the top of the

su/jointfilesconvert/1717682/bgroup strips (see “Meter” above).

1 2 ... 20 21 22 23 24 25 26 27 28 29 30 31 32

Kommentare zu diesen Handbüchern

Keine Kommentare

Cadac LIVE1 Bedienungsanleitung Seite 25

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Schalttafel Cadac LIVE1